刷机失败原因，创维8r98

维佳

创维电视雪花。我上面显示停止运行。优盘刷机试了几次刷不进去。不知道什么原因，打印信息也看不懂，请教大师看看是什么原因，谢谢
附上U盘的固件图片



U-Boot 2012.07-svn574318 (Sep 13 2013 - 16:47:46)

GPU : BISR testing...
GPU : Finish BISR testing (OK)
SCPU: BISR testing ....
SCPU: Finish BISR testing
CPU  : Cortex-A9 dual core
Media: eMMC BP0
DRAM:  1.5 GiB
Watchdog: Enabled
init_amp_prepare
Board: Tv010 v2 512M_1G Board
POWER ON: AC
Cache: Enabled
Non-Cache Region: 1 MB@0x07900000
MMC:   
emmc:mmc_initial(1) Sep 13 2013 16:48:02
RTD299x eMMC: 0
Device: RTD299x eMMC
Manufacturer ID: 11
OEM: 100
Name: 004G9
Tran Speed: 52000000
Rd Block Len: 512
MMC version 4.0
High Capacity: Yes
Capacity: 3.7 GiB
Bus Width: 8-bit
Extern param: MMC blk:0x7c (to 0x9000)
Factory: MMC
Factory: seq:0x19eb, blk:0xc000(pp:0), size:0x19ac00 (to 0x7000000)
get_bootparam:
------------tmp/factory/bin_panel/000BootParam.h found
BOOT_POWER_ON_MODE=1
BOOT_LOGO_ENABLE=1
CUSTOM_VIDEO1_LENG=0
CUSTOM_VIDEO2_LENG=0
BOOT_MUSIC_ENABLE=0
CUSTOM_AUDIO1_LENG=0
CUSTOM_AUDIO2_LENG=0
LOCAL_UPGRADE_EN=0
boot_power_on_mode=1
get_layout:
------------tmp/factory/layout.txt found
BOOTPART=0
TAG=21
init_amp
Factory_RO: MMC
[FAC_RO] No factory_ro data in eMMC
[ENV] read_env from factory failed
[ENV] Using default environment variables

ee read 368, 6
name=EEP_I2C ppcb_enum.Name=EEP_I2C, ppcb_enum.info=4
EEP_I2C=4
name=EEP_DEVICE_ADDR ppcb_enum.Name=EEP_DEVICE_ADDR, ppcb_enum.info=50
name=PIN_EEP_WP ppcb_enum.Name=PIN_EEP_WP, ppcb_enum.info=100011304
m_PIN_EEP_WP = 0x100011304
a. Eeprom_Read-macaddr is bc83a7b03f89
set_mac_cmd is bc:83:a7:b0:3f:89
Panel: Use parameters in tmp/factory/bin_panel/panel.bin
Panel: sky_v420dk1
panel_init_1st
Panel: ulFreq:297000000, nDPLL:269999360, Mcode:60, Ncode:3, offset:fffff333
DispI : Finish BISR testing done
DispD : Finish BISR testing done
========= 4K2K Millet3 Series LVDS Panel ==========
In:    serial
Out:   serial
Err:   serial
Net:   rtl8139: REALTEK RTL8139 @0xb8016000
Hit Esc or Tab key to enter console mode or rescue linux:  0 ======== Checking into android recovery ====

boot_ac_on=1
#@# do_usb(481) is_usb_ac_on 0
(Re)start USB...
USB0:   #@#  usb3_phy_setting(108) +++ 20130415
#@#  usb3_phy_setting(209) ---
#@#  usb2_phy_setting(214) +++ 20130510
#@#  usb2_phy_setting(294) ---
#@#  usb3_mac_setting(301) +++ 20130510
#@#  usb3_mac_setting(384) ---
Register 5000140 NbrPorts 5
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... usb_init 120
usb_get_configuration_no: failed to get descriptor - too long: 1045
usb_new_device: Cannot read configuration, skipping device 0c45:6340
USB device descriptor short read (expected 18, got 8)

#@# usb_hub_configure(512) skip the device in usb3 port 5!
usb_init 129
4 USB Device(s) found
       scanning usb for storage devices...
#@# usb_storage_probe(1301) skip usb3 device(0x210) !
0 Storage Device(s) found

** Invalid boot device **
pUsbFirstFileName = NULL
stopping USB..

Start Boot Setup ...
         FW Table to 0x06ff0000, size=0x00000400 (0x06ff0400)
         FW Table fr 0x02000000, fw count: 6
Normal boot fw follow...
Linux Kernel:
         FW Image to 0x00108000, size=0x00996784 (0x00a9e784)
         FW Image fr 0x02008000 (non-lzma)
Audio FW:
         FW Image to 0x81700000, size=0x00207dc0 (0x81907dc0)
         FW Image fr 0x0299e800 (non-lzma)
Video FW 1:
         FW Image to 0x81a00000, size=0x002b8830 (0x81cb8830)
         FW Image fr 0x02ba6600 (non-lzma)
Video FW 2:
         FW Image to 0x81d00000, size=0x000b218c (0x81db218c)
         FW Image fr 0x02e5f000 (non-lzma)
ECPU FW:
         FW Image to 0x00004000, size=0x00001f7d (0x00005f7d)
         FW Image fr 0x02f11200 (non-lzma)
Video[image] data 1:
         FW Image to 0x82500000, size=0x000420f1 (0x825420f1)
         FW Image fr 0x02f13200 (non-lzma)
Enable VCPU1
Enable VCPU2
aa 0xffff0010, 0x0, 0x0, 0x0
Release HW semaphore
ABCD[BOOT_AIO][0]  0x00000000
[BOOT_AIO][1]  0x00000000
[BOOT_AIO][2]  0x00000000
[BOOT_AIO][3]  0x00000000
[AIO_PATH] use default setting!
[AIO_PATH] src_sel_scart1    =  0x00000001
[AIO_PATH] src_sel_headphone =  0x00000001
[AIO_PATH] src_sel_pcm_dac0  =  0x00000007
[AIO_PATH] src_sel_pcm_dac1  =  0x00000007
spdif raw from PB
enable_clock 34 hold_hw_semaphore
VVwwaaiitt  
VCPU1: BISR testing ....
VCPU1 : Finish BISR testing done


VCPU2: BISR testing ....
VCPU2 : Finish BISR testing done

aa 0x73811a3c, 0xc07b5a27, 0x8004003, 0x0
Release HW semaphore again
V2go V1go RosStartTaskCreatReoHsoSokta r13t2
sz apskktQC r e0xa8t1edHo8ock 610302,
   V 08  p1k6 tQ8
0x81c71900, sz 8 16 8
V0 pktQ  0xa1c71900  0xa1d8c600
[VO] Force DTG FRC
[VO]SynGen= 0x80000004
[VO]SynGen= 0x80000004
~~Vodma Dis 0 0 size 0
[vo] VODMA(0) ForceBG(0)
VP_PowerOnVideo 33
~vbm create  0xa3004000, 34872
VBM: configured to DivX HD!
[vo] ShowChannel(p1)
POV: image filter testing
+++[RequestBuffer] width 1920, height 1080 ret 268435456
POV: request Buffer, Y_BufID = 0
+++[RequestBuffer] width 1920, height 1080 ret 268435456
POV: request Buffer, C_BufID = 1
POV: image filter testing Y_bufID 0, C_BufID 1

(IMG) JPEG detect!!IMG_DEC: Create Filter fmt 0
SE_SCALER_Init96): base0  0x84974000, sz0  0x00800000,base1  0x85174000, sz1  0x00800000SE_SCALER: procBuf  0x85974000, sz0  0x00400000
IMG_DEC: send ringbuffer cmd to Dec
JPEG_DEC: base= 0x82500000 limit= 0x82542100 Wr= 0x825420f1 Rd= 0x82500000
IMG_DEC: send Decode cmd to Dec
JPG_DEC: IMG_DECODE
IMG_DEC: send cmd to Scaler

(Adobe) set saw_Adobe_marker TRUE!!
(Adobe) set saw_Adobe_marker TRUE!!
(THUMB) IS USING THUMB 0, w 160, h 90, tgt_w 1920, tgt_h 1080!!
(JPEG) IsC 0, w 1920->1920, h 1080->1080, hor 0, ver 0!!
(JPEG) IsC 1, w 3840->3840, h 1080->1080, hor 0, ver 0!!SE_SCALER: MPO 1 0

(JPEG_COMP) IS_PROG 0!!
(SendScalerEnd) IsShowPic 0!!JPG_DEC: decode time=10530 w=1920 h=1080
IMG_DEC: destroy
JPG_DEC: decode time=11784 w=1920 h=1080
POV: image filter testing DONE
[vo] VODMA_SyncGen_Check: p1, pic 1
[VO]SynGen= 0x80800004
V1 pktQ  0xa1d8c600  0xa1c71900

[vo] ipg1080p_frc_fhd_dibypass !!!
[vo] VODMA_SendVOInfo
ptSlrVoInfo  mode=10
h_start=140
v_start=13
h_width=1920
v_length=1080
h_total=2200
v_total=1112
chroma_fmt=0
progressive=1
h_freq=675
v_freq=600
pixel_clk=148500000
i_ratio=0
source=0
ptSlrVoInfo  afd=8
3d_mode=0
force2d=0
NULL == ptSlrVoInfo
ShowStillPicture~~
[ao_Init] ver_C
bf [SB2_INSTAT] =  0x00000000
af [SB2_INSTAT] =  0x00000000

HDMI Raw Enable: MPG AC3 DTS MPEG2 AAC DDP WMAPRO MLP

SPDIF Raw Enable: MPG AC3 DTS MPEG2 AAC DDP WMAPRO MLP

Force 2ch Format: DTS DTSHD AC3 DDP MLP AAC WMAPRO

No Power On Music
[A] SetAudioDone to addr  0xa0001415 value  0x00000002
panel_init_2nd
ampinit at panel flow, 2373
init TAS5711 (2995)
WARNING[773879]OV: Wait system to STOP Power on Video!(bVideoDone 2)
Kernel command line: androidboot.console=ttyS0 console=ttyS0,115200 envp=100700 flashtype=emmc mmcparts=rtkemmc:3743744k,524288k(/system),1048576k(/data),262144k(/cache),358400k(/skydir),81920k(/dtv),16384k(/res),768000k(/skyota) reclaim=64M@32M last_image=8M@96M quiet
Starting kernel ...
[    0.212000] [linux][CBUS] MHL_init_module
[    0.216000] [linux]CBUS: register sucess!!! IRQ 57
-------------------
Audio Version = 577189 (ve˙n[    0.292000] mtdoops: mtd device (mtddev=name/number) must be supplied
[    0.360000] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    0.496000] EXT4-fs (mmcblk0p2): VFS: Can't find ext4 filesystem
[    0.500000] fs_mgr: Cannot mount filesystem on /dev/block/mmcblk0p2 at /data
[    0.508000] init: fs_mgr_mount_all returned an error
root@android:/ # WARNING[1879335]OV: Wait system to STOP Power on Video!(bVideoDone 2)
[vo] ShowChannel(p255)
[vo] HideChannel(p1)
[vo] VODMA(1) ForceBG(1)
~detect rx cmd 18 st 0
VIDEO_RPC_VideoDestroy Called!~VBM_Destroy
~clear gpVBM
~VBM_Destroy ret 0
VBM_Destroy 268435456!VMM_Destroy 268435456!VIDEO_RPC_VideoDestroy Return!POV: Release Video
[audio] AUDIO_CONFIG_CMD_VOLUME  0x00000185
[audio] AUDIO_CONFIG_CMD_VOLUME  0x00000185
spdif fix volume shound from PB ch 4/5 path
[ao_Set_OutputSamplingRate2] fs = 48000(8)
[AO] ao_Set_OutputSamplingRate2() TCON ASRC clock path patch on
-------------------
Audio Version = 577189 (venus or neptune)
Common Version = 571929
Binary src compiled at Sep 24 2013 19:14:46
Note =
-------------------
~vbm create  0xb0150000, 34872
VBM: configured to DivX HD!
~vbm already created  0xb0150000
VBM: configuration unchanged!
[AUDIO] Receive debug memory address x  0x818f3660 !
[AUDIO] Debug memory address *x is  0x1e43c000 !

SetLPrintBuffer: header address =  0x00000000
VIDEO_RPC_SetDebugMemory Called!High =  0x00000000, Low =  0x00000000
The following Format is supported:
WARNING[1]:VO: don't support this API line 123
Video pli memory addr[0]= 0xb0160560
Video pli memory addr[1]= 0xb01605e0
Video pli memory addr[2]= 0xb0160660
Video pli memory addr[3]= 0xb0160a40
Video pli memory addr[4]= 0xb0160af4
Video pli memory addr[5]= 0xb01681a0
Video pli memory addr[6]= 0xb01680f4
Video pli memory addr[7]= 0xb016814c
Video pli memory addr[8]= 0xb016817c
Video pli memory addr[9]= 0x00000000
scalerDrv_Init
Please set RTNR table before update RTNR table.

-[vo] FR Ctrl, Table[0]-
[vo] force: enable 0, framerate 59940
[vo] double dvs enable: 0, threshold 31000
[vo] High-Bound check: enable 1, Bound 60000, Adjust 60000
[vo] Low-Bound check: enable 0, Bound 47952, Adjust 59940

-[vo] FR Ctrl, Table[1]-
[vo] force: enable 0, framerate 59940
[vo] double dvs enable: 0, threshold 31000
[vo] High-Bound check: enable 1, Bound 60000, Adjust 60000
[vo] Low-Bound check: enable 0, Bound 47952, Adjust 59940
[vo] Force2D( p1, 0)

-[vo] FR Ctrl, Table[0]-
[vo] force: enable 0, framerate 59940
[vo] double dvs enable: 0, threshold 31000
[vo] High-Bound check: enable 1, Bound 60000, Adjust 60000
[vo] Low-Bound check: enable 0, Bound 47952, Adjust 59940

-[vo] FR Ctrl, Table[1]-
[vo] force: enable 0, framerate 59940
[vo] double dvs enable: 0, threshold 31000
[vo] High-Bound check: enable 1, Bound 60000, Adjust 60000
[vo] Low-Bound check: enable 0, Bound 47952, Adjust 59940
[vo] Set3DMode( p1, 0)

-[vo] FR Ctrl, Table[0]-
[vo] force: enable 0, framerate 59940
[vo] double dvs enable: 0, threshold 31000
[vo] High-Bound check: enable 1, Bound 60000, Adjust 60000
[vo] Low-Bound check: enable 0, Bound 47952, Adjust 59940

-[vo] FR Ctrl, Table[1]-
[vo] force: enable 1, framerate 120000
[vo] double dvs enable: 0, threshold 31000
[vo] High-Bound check: enable 1, Bound 60000, Adjust 60000
[vo] Low-Bound check: enable 0, Bound 47952, Adjust 59940
SCALERIOC_SET_PANEL_INFO
scalerInfo_setPanelInfo
VT/DV.STA/END=1125/16/1096, PanelType=1
~~Vodma Dis 0 0 size 67108864
[vo] VODMA(0) ForceBG(0)
enter scalerVIP_SET_DCC_LEVEL_TABLE

scalerVIP_SET_DCCHist_Factor_TABLE
scalerVIP_SET_dbDCCHisto_TABLE
xAE] csaommpmolenr/aVteP pr_eF I= LT( E0Rx0_0C0r0bbe8a0t, e0
e00V0P0b_bFI80LT),E Rno.cw =( (3 06x00900)bb8:0 C,r 0ex0a0t0e0 vbib80d)
eroAE ] eSnRcCo odff
  !
+++ Filter Enc Create
VP_FILTER.c(399): Create done, filter = 0xb0930000!
~vencfilt init 2 255 4
VP_FILTER.c(363): Create video capturer!
FILTER_CAPTURER_Create!
VP_FILTER.c(641): SetRefClk...
VP_FILTER.c(643): SetRefClk...done
VP_FILTER.c(447): Connect source: pinID = 1, comp =  0xa6a200b8!
VP_FILTER.c(459): Connect destination: pinID = 1, comp =  0xb09300f8!
VP_FILTER.c(481): Connect done!
Capin_InitRingbufStream:base: 0x0c800000, limit: 0x0d000000
VP_FILTER.c(499): InitRingBuffer...
VP_FILTER.c(523): InitRingBuffer...done
VP_FILTER.c(499): InitRingBuffer...
VP_FILTER.c(523): InitRingBuffer...done
VP_FILTER.c(557): Pause...
VP_FILTER.c(561): Pause...done
VP_FILTER.c(538): Run...
~vpp proc cmd 16
VP_FILTER.c(542): Run...done
[    5.716000] scsi 0:0:0:0: Direct-Access     General  USB Flash Disk   1100 PQ: 0 ANSI: 6
[    5.728000] sd 0:0:0:0: [sda] 62980096 512-byte logical blocks: (32.2 GB/30.0 GiB)
<APP> create start( 0x90415620)

<APP> PP Create!!!!!!
<APP> SmoothPlayback create
<APP> create end
common/VP_FILTER_Create
VP_FILTER.c(369): Create video encoder!
+++ Filter Enc Create
VP_FILTER.c(399): Create done, filter = 0xb0970000!
~vencfilt init 0 255 2
[AE] samVplPe_rFaILtTe EprR.e c= (( 06x040001bb)80:,  0Sxe00t0R0ebfbC80lk),. .n.ow
t=V (P_ 0FxI00L0T0bERb.80c(, 06x04003)0b:b 80S)e
R[eAEf] ClSRCk o.ff.
.done
VP_FILTER.c(499): InitRingBuffer...
VP_FILTER.c(523): InitRingBuffer...done
VP_FILTER.c(499): InitRingBuffer...
VP_FILTER.c(523): InitRingBuffer...done
VP_FILTER.c(499): InitRingBuffer...
VP_FILTER.c(523): InitRingBuffer...done
~vpp proc cmd 36
~~vpp rx unknown cmd
++++ set res in 62176 0 out 320 240
~vpp proc cmd 25
~vpp resol 320 240
~vpp proc cmd 32
~vpp fr 10
enc_slc rx fr 10
~vencfilt bitrate 8974000, rcmode 2
enc_slc rx rc 2, br 8974000, aq 0
<APP> switch focus: 0xfffffffe -> 0x00000000
VP_FILTER.c(557): Pause...
VP_FILTER.c(561): Pause...done

[AO Reinit State] reinit_flag =  0x00000004
[AO][SPDIF] subtype(0)
[AO][raw config:HDMI(0),SPDIF(0)]
[AO]SPDIF SELECTION: PCM FIFO
<APP> max_out_samplerate type  0x00000000
VP_FILTER.c(538): Run...
~vpp proc cmd 16
VP_FILTER.c(542): Run...done
scalerIRQ_setTVScanMode
~~Vodma Dis 0 0 size 67108864
[vo] VODMA(0) ForceBG(0)
ENUM_AIN_SWITCH_FOCUS (fcs: 0x00000000,mux: 0x000000ff)
TS focus[0] =  0x00000000, mux_in =  0x00000000
PB focus[0] =  0x00000000, mux_in =  0x000000ff
set new source clk ready
<APP> SpeedScale delaybuf flush  0x00000000
[AI][HPT] ai_call_hpt: 0x00000000, ai_flush: 0x00000000 END
[Pass through  0x00000000: 0x00000001]
ENABLE WrADMA ai_focus_id: 0x00000000
$$$deliever info ok$$$
[AE] samplerate pre = ( 0x0000bb80, 0x0000bb80), now = ( 0x0000bb80, 0x0000bb80)
[AE] SRC off
[AO] DAC change point occur: rp  0xb0de0000 cptr  0xb0de0000  0x0000bb80  0x0000bb80
[AO Reinit State] reinit_flag =  0x00000003

============[AO][high priority task]===============
[DAC  0x0000bb80 ->  0x0000bb80]
send system info  0x0000bb80
[AO][SPDIF] subtype(0)
[AO][raw config:HDMI(0),SPDIF(0)]
[AO]SPDIF SELECTION: PCM FIFO

============[AO][high priority task]end============
[AO][TS]Enable RdAdma(v/a: 0x00001000/ 0x00004000),thd=20ms
[AO][PB]Enable RdAdma(v/a: 0x00001000/ 0x00004000),thd=20ms
ENUM_AIN_ATV_SET_CLOCK
<APP> SpeedScale delaybuf flush  0x00000000
[AI][HPT] ai_call_hpt: 0x00000000, ai_flush: 0x00000000 END
ENUM_AIN_ATV_SET_CLOCK
<APP> SpeedScale delaybuf flush  0x00000000
[AO][TS] Underflow
[AI][HPT[AO][PB] Underflow
Underflow
[Pass through  0x00000000: 0x00000001]
ENABLE WrADMA ai_focus_id: 0x00000000
$$$deliever info ok$$$
[AE] samplerate pre = ( 0x0000bb80, 0x0000bb80), now = ( 0x0000bb80, 0x0000bb80)
[AE] SRC off
[AO] DAC change point occur: rp  0xb0dee000 cptr  0xb0dee000  0x0000bb80  0x0000bb80
[AO Reinit State] reinit_flag =  0x00000003

============[AO][high priority task]===============
[DAC  0x0000bb80 ->  0x0000bb80]
send system info  0x0000bb80
[AO][SPDIF] subtype(0)
[AO][raw config:HDMI(0),SPDIF(0)]
[AO]SPDIF SELECTION: PCM FIFO

============[AO][high priority task]end============
[AO][TS]Enable RdAdma(v/a: 0x00001000/ 0x00004000),thd=20ms
[AO][PB]Enable RdAdma(v/a: 0x00001000/ 0x00004000),thd=20ms
ooo---scalerVIP_GetIntraRange= 0x00000005 ---ooo
DCC_MODE_Select =2

维佳

开机，最后显示    ，，，，，，，停止运行，如图